Intrepid Video & Electronics WELCOME! Copyright © Intrepid Video & Electronics |
| CCA192 | TV stays on for a few secs. | D201 in sys control |
| CCR095AT01 | Shuts dowm 30 minutes | Q1012 (ECG2362) check for bad solder power supply |
| CCR132 | *Vertical compression
at bottom, stretched at top *Parts ID |
*C06(1/50v), jump R06
w/ 1k resistor. May have to try several values to get
best Lin. *Q2-2SK212, use original |
| CCR138AT01 | Tape loads in play, no eject | Kit#4822 3101 0657, install lg white gear w/ arrow pointing to arrow on arm gear & cassette down. |
| CCR190AT03 | *Unit shuts down *Shuts down, 112v shoots to 175 *Picture bright with reetrace lines |
*C07 on hot side &
Q05 *Q15 B/E shorted, R56 in power supply(18k @ 1/4 w) *C12(4.7/250v) off FBT |
| CCS135 | Dead | Loose connection on coil, 5588 on 110v to HOT |
| CCS138AT01 | *Tape loads,no play,no
eject *Dead, no relay click *Dead *Tape stuck, TV won't stay on. |
*Kit #4822-3101-0657,
install lg white gear w/ arrow pointing to arrow on arm
gear and casette down *Shorted diode 6371 in power supply (1N5408) *6334 diode leaky(4835 1303 7792), check R331, R3332, R3340, IC7310 *Gear on worm shaft cracked, 4822 3103 2198 |
| CCT090AT02 | *Video inoperable *TV/VCR won't power up *Won't shut off-press power, pic goes black. HV is there & red bar across screen |
*IC301, M52339SP *6v reg-IC651 *C581 |
| CCT132 | *No audio *Tape stops playing after 15 secs. *Dead, no emitter voltage on Q604 |
*Solder C854 *Replace reel sensors *R607 open, remove one leg to check |
| CCT190AT01 | *No vertical
deflection *No power, squeal from power supply *Dead, no emitter voltage on Q604 |
*Re-solder J501,
ground line on sub board *IC603 5v reg (AN7805-ECG960) *R607 open, remove one leg to check |
| CCU091 | Dead, HV starts at plug in, shuts down. | Q601(10.7reg) shorted [A1649] |
| CCU131 | *Dead *No power, 112vdc momentarily normal, then 0v |
*150v zener, on 112v
source shorted, R604 increased oin value, should be 0.33
@2w *KIA7806, 6v reg on main PCB |
| CCU133AT01 | Shuts down in three seconds of HV and good pic | Clean contacts in micro switch on main pcb, under vcr-resolder coax inside receiver |
| CCX132AT02 | Parts ID | T/U reel 4835 1307 7911 |
| CCX193AT32 | *Unit shuts down in
10-15 secs, TV & tape mode. *Will not come on all the time *Part ID |
*Replace center LED *SW202(rew sw) leaky, dragging down 5v to pin 2(IC201). Also LED/prism kit(X480195) *D620-4835 1303 7899---ECG5025A |
| CCX252AT32 | *Part ID-brake slide *Turns off after 15 mins, can be turned on again. |
*4835 4029 7723 *Repair/solder pins/pads on R1651 |
| CCZ132 | *Takes tape, shuts
down-no capstan *Machine gun noise when loading tape |
*Replace capstan, NAP#
4835 3612 7158 *Reposition shaft for worm gear assembly. Shaft is too far forward |
| CCZ190 | Load, eject problems | Loose, broken tab on cassette drive lever sub assembly, under load motor. Funai # OVSA08827 |
| CCZ191AT32 | *TV/VCR won't come on *Part ID |
*IC541(LA7837),
R545(6.8 ohm) *Rt side guide post--#4835 4645 7361 |
| CRK120AT02 | Has audio, No pic (HV) | R802, 3W, 5.6 ohm; Q551-ECG2302; C553 (222K,2kv.) |
| CRL131AT01 | Has audio, no video. | Relay 601, bad solder. |
| CRL191AT03 | Snowy on tuner and VCR playback | Q701 (2SD2005), C713 |
| CRN130AT01 | *No audio from tuner *No power |
*Poor solder at audio
jacks. *C1026 |
| CRN135 | Dead | C1(120/200v) ope in VCR power supply |
| MVC620(GHV1265M) | Won't always load tape around heads | Replace load motor |
| MVC627 | Tape stuck in unit, load gears, mode sw-OK | Load motor worm gear slid toward motor, on shaft. |
| VR431 | No power, will load tape, display shows "PL" | Parental lock. Hold power on remote for 10 secs. |
| VR1260 | Slow to turn on when plugged in. | C1016, 330/6.3v-in power supply |
| VR3330(VR9130) | No EE pic | Pin 1 of demod less than 5v, Q7001 (483513047709) |
| VR3410AT01 | Confused, intermittently goes play to FF to REW | C5 in primary is low. (4.7/200v) |
| VR3460AT01 | Unit goes in FF when tape is inserted | Defective mode switch |
| VR3560AT01 | *Dead, fuse OK, may be
low whine noise *Display dims-shuts down. |
*C107(4.7/250v),
C128(470/16v) *C128, C129 in power supply |
| VR6685 | Intermittently power up, display flashes | Power supply: C16 (330/16v),C17(1000/6.3v) |
| VR8445 | Breaking tapes on FF/REW | Spray out end sensors |
| VR9020(VR9040) | *Erases tape in play
back *Capstan won't turn |
*Check pin 35 of IC601
& Q305. If base is more pos., than emmitter, replace
Q305, if less-replace IC601. *C412 |
| VR9040(VR9020 | *Erases tape in play
back *Capstan won't turn |
*Check pin 35 of IC601
& Q305. If base is more pos., than emmitter, replace
Q305, if less-replace IC601. *C412 |
| VR9120 | Color not stable on play | C16(330/16v), check all caps in power supply |
| VR9130 | *No pic in EE *Picture jumps, noise bars top of screen, no color |
*Pin 1 of demod less
than 5v, Q7001 (483513047709) *IC3221(MN8505) 4835 2091 7318 left rear corner of deck |
| VR9160 | Poor playback, tracking lines | *3.3/50v cap on lower
cylinder *Check bottom of guide posts for missing/loose pins |
| VR9240 | Picture bounces | Left side guide post |
| VR9241 | No audio | Audio IC301-- 4835 2098 8046 |
| VR9261 | Rec w/ oscillation lines, low/no audio | Power supply C32(470/16v),C34(22/50v), re-solder cracked joints |
| VR9320(9321.9339.9340) | Intermittent capstan speed after 15 minutes. Change is abrupt. | Capstan belt gets static, replace w/ 4835 3583 7125 |
| VR9321(9320.9339.9340) | Intermittent capstan speed after 15 minutes. Change is abrupt. | Capstan belt gets static, replace w/ 4835 3583 7125 |
| VR9339(9320.9321.9340) | Intermittent capstan speed after 15 minutes. Change is abrupt. | Capstan belt gets static, replace w/ 4835 3583 7125 |
| VR9340(9320.9321.9339) | Intermittent capstan speed after 15 minutes. Change is abrupt. | Capstan belt gets static, replace w/ 4835 3583 7125 |
| VR9341(Funai) | Dead | Q1002(2SC44535), Q1001(2SC4204),R1014(0.82-1/4w),D1014(NTE519) |
| VR9362 | Picture rolls | Replace brake band assembly |
| VR9610 | Dead, hissing sound. | C12(330/18v) leaky. |
| VR9624 | Dead | Caps-5, 9, 10, 11, 12, 14, 15, 19. |
| VR9642 | Unit dead, no display. Only accepts tape. | Bad caps in p/s. C19(1/50v); C15, C16(330/6.3v); C9(2.2/50v) |
| VR9664(Panasonic) | Color bars in play back | C14-15-09 |
| VR9668 | *Dead, IC2005, Q1202
overheat *Video input distorted, pulling |
*C1012 C8366, 100/6v |
| VR9740 | *Dead *Tuned stations fade in/out, sometimes disappear. |
*Replace all brown
caps on secondary of SMPS. *Replace tuner. |
| VR9770 | Display won't light if line voltage above 95vac | Q1006 (2SB1050) in power supply |
| VR9860AT02 | No channels above 9-just snow | 0.01 cap on pin 1 of tuner |
| VR9960 (VG4009) | Stops after 3 seconds | Q1202, on main pcb-12v REG-DEF. |
| VRT242 | Ratcheting-worse in FF/REW | Capstan bearings are dry |
| VRT245 | Power light on, no pl, ff, rew | Q504(ECG2357) inder basket |
| VRT262 | *No functions other
than on/off, won't accept tape *No eject, won't accept cassete |
*D1501, check for
loose connection *Missing spring & tab broken that shifts mechanism when ejecting. |
| VRT344 | Power supply squeals, dead | C20 100/10v, in power supply |
| VRT362(VRT442) | Noisy chroma in play back, esp. SLP | Remove R254 |
| VRT442 | *Noisy chroma in play
back, esp. SLP. *At power goes into REW. |
*Remove R254 *Clean white dust on bottom of prism. |
| VRU222(VRU242) | *Won't power up, no
functions. *No tuner a/v,playback a/v OK *Loads tape, no capstan. *Dead *Capstan speed & audio fluctuates |
*Q55, main
pcb(KSA103M) ECG2358 *L702, 18uH 4835 1575 7965, 5-volt to tuner. *R534 22K 1/4 watt 4385 1113 7177 *Q02 IC01 D16 D17 *Replace capstan belt, static build up. |
| VRU242(VRU222) | *Won't power up, no
functions. *No tuner a/v,playback a/v OK *Loads tape, no capstan. *Dead *Capstan speed & audio fluctuates |
*Q55, main
pcb(KSA103M) ECG2358 *L702, 18uH 4835 1575 7965, 5-volt to tuner. *R534 22K 1/4 watt 4385 1113 7177 *Q02 IC01 D16 D17 *Replace capstan belt, static build up. |
| VRU262 | *Keeps rejecting
cassette *Poor video-capstan jerky-may be intermittent *No capstan movement |
*Replace LED and end
sensors. *Static build up on capstan belt-replace w/4400R-003A *R534-22k-1/6w, from mode to sys control |
| VRU362AT01 | Loads tape, retracts, eats tape on eject | Replace LED, end sensors |
| VRU422 | Tape gopes to FF when inserted | Re-solder C456, close to micro, or replace. |
| VRU462 | *Shuts down after tape
inserted. *No play, pinch roller not meeting capstan. |
*Replace IC1201 5835
2098 8168 *Replace lever assembly, beneath roller, #PQ46342D-10 |
| VRU662 | |Capstan speed fluctutates | Static buildup on capstan belt, replace. |
| VRX222 | *Unit slows down after
30 mins of play. *Part ID: |
*R607 (100K) use 150K *LED (4835 1308 7139); Q504, Q505(4835 1304 8076); prism(4835 4029 7731) |
| VRX240AT22 | Will not load tape to heads, eats tapes | Replace broken guide, T-preparation(4835 4029 7758) |
| VRX262 | Shuts down 30 minutes, in play/rec. | R607(use 150k), D511, Q511-EDI kit 07-426(1-800-426-6423) |
| VRX364AT21 | PL, REW, FF stops in 5-10 secs, powers off | D511, Q514, (903-01487-01 & 921-1898) Zenith numbers. |
| VRZ222 | Plays 15 secs, then reads ERR 1 | D511 (4835 1308 7092) |
| VRZ242 | *Insert tapes, won't
load *Shuts down 15 seconds *Tape plays 15 secs, shuts down. #1 flashing |
*Cap 82/200v, in power
supply. *Replace Q514, IR sensor/replace R607 w/ 150K *Replace center LED |
| VRZ263 | No capstan | Bad solder on capstan IC. |